5 8 inch oxygen acetylene hose

Just fill in the form below, click submit, you will get the price list, and we will contact you within one working day. Please also feel free to contact us via email or phone. (* is required).

  • Amazon.com: oxygen and acetylene tanks

    Goplus 50ft Twin Welding Torch Hose Oxy Acetylene Oxygen Cutting 1/4-Inch 300psi. 4.1 out of 5 stars 281. $52.98 $ 52. 98 ($1.06/Foot) Get it as soon as Wed, Dec 15. FREE Shipping by Amazon. More Buying Choices $49.99 (3 new offers) SÜA - Oxygen and Acetylene Regulators Welding Gas Gauges -Pair - Rear Entry - LDP series.

    Get Price
  • Hobart 770502 Medium Duty Oxy-Acetylene Kit - Spot

    ZenStyle Oxygen & Acetylene Gas Cutting Torch and Welding Kit Portable Oxy Brazing Welder Tool Set with Two Hose,Regulator Gauges,Storage Case 4.3 out of 5 stars 664 1 offer from $139.99

    Get Price
  • Oxy-fuel welding and cutting - Wikipedia

    2021-12-10u2002·u2002Oxy-fuel welding (commonly called oxyacetylene welding, oxy welding, or gas welding in the United States) and oxy-fuel cutting are processes that use fuel gases (or liquid fuels such as gasoline) and oxygen to weld or cut metals. French engineers Edmond Fouché and Charles Picard became the first to develop oxygen-acetylene welding in 1903.Pure oxygen, …

    Get Price
  • Oxy Acetylene Welding Pressure Settings Chart Set Up

    2021-9-24u2002·u2002Oxy Acetylene Welding Set Up and Pressure Settings Chart : The first we must Clean the nozzle, because if the head of the nozzle dirty will cause flame bad. Open Regulator Oxygen and Acetylene, set until the pressure matching with what do you want or for acetylene 5 to 7 psi and Oxygen 7 to 10 psi.

    Get Price
  • Oxy Acetylene Cutting Torch Pressure Settings (Regulator ...

    This recommendation applies when cutting less than 1.5 inch steel with the use of propane, propylene or natural gas. Oxy Acetylene The recommended setting for multi-hole cutting is the oxygen regulator at 40 psig with the acetylene regulator setting at 10 psig.

    Get Price
  • 11 Best portable oxyacetylene torch kits

    2020-10-22u2002·u2002To give an idea, if you'll be welding 1/16-inch steel, you'll need 8 – 20 psi of oxygen and about 5 psi of acetylene. Likewise, for cutting up to 2-inch steel, you'll need 40 – 50 psi of oxygen and 5 psi of acetylene. Bear in mind that these …

    Get Price
  • 1910.253 - Oxygen-fuel gas welding and cutting ...

    2021-12-10u2002·u2002Hose connections and hose complying with paragraph (e)(5) of this section may be used to connect the outlet of a manifold pressure regulator to piping providing the working pressure of the piping is 250 psi (1.7 MPa) or less and the length of the hose does not exceed 5 feet (1.5 m). Hose shall have a minimum bursting pressure of 1,000 psig (6.8 ...

    Get Price
  • Hose

    Choose from our selection of hose and hose fittings, tubing and tube fittings, duct hose and duct hose fittings, and more. In stock and ready to ship.

    Get Price
  • Hose Barbs

    Also known as ball-seat hose nipples, these fittings consist of a barbed shaft with a rounded end that sits inside a female threaded nut. When mated with a male threaded fitting, the rounded end presses tightly against the inside of the male threads for a better seal than a single-piece fitting. Once assembled, insert the barbed end into hose and secure with a clamp or a crimp-on hose …

    Get Price
  • How to Anneal Copper: 13 Steps (with Pictures) - wikiHow

    2020-8-16u2002·u2002Connect 1 hose to each tank to set up the acetylene torch. The torch itself—which will produce the flame—will have 2 hoses coming out of it. Connect the red welding torch hose to the acetylene tank, and the black hose to the oxygen tank. The acetylene gas will start the flame and the oxygen will continue to feed the flame once it's lit.

    Get Price
Inquiry Now